Barracuda Networks 4 Guide d'installation Page 53
- Page / 142
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Basic Tab 53
Resetting the System Using the Front Panel
Pressing the Reset button located on the front panel of the Barracuda Spam Firewall does the
following:
• Reboots the system
• Resets the firmware version to the factory setting
Do not push and hold the RESET button for longer than a few seconds as this changes the IP address
of the system. Pushing and holding the RESET button for 8 seconds changes the default IP address to
192.168.1.200. Holding the button for 12 seconds changes the IP address to 10.1.1.200.
Automating the Delivery of System Alerts and Notifications
The BASIC-->Administration page lets you configure the Barracuda Spam Firewall to automatically
e-mail daily system status reports and system alerts to the e-mail addresses you specify.
Enter the e-mail addresses (comma separated) in the provided field and click
Save Changes. The
daily system status reports are sent out nightly and the system alerts on an as-needed basis.
The daily system status report shows the number of messages blocked, quarantined, tagged and
allowed for each hour of that day.
Changing the Operation Mode of the System
Your Barracuda Spam Firewall can operate in one of two modes: inbound mode or outbound mode.
The most commonly used mode is the inbound mode, which scans incoming messages for spam and
viruses. If your organization has a reason to scan outgoing messages from your users, you can
configure your system to operate in outbound mode.
A Barracuda Spam Firewall can only be configured for one mode.
If you choose to change the mode from inbound to outbound (or vice versa), note the following:
• All your message log data and quarantine messages are deleted.
• System configuration remains in tact. However, you should verify that the configuration options
are appropriate for outbound mode.
Restart Reboots the system.
Reload Re-applies the system configuration should the recent changes not
take effect.
Caution
Shutting down, resetting, or reloading the system can cause interruptions in e-mail delivery.
Table 4.14:
Button Description
- Version 1
- Copyright Notice 2
- Trademarks 2
- Contents 3
- Chapter 1 9
- Introduction 9
- Overview 10
- Understanding Spam Scoring 11
- Figure 1.2: 11
- Inbound and Outbound Modes 12
- Technical Support 12
- Warranty Policy 12
- Table 1.1: 13
- Basic Tab 14
- Table 1.2: 14
- Block/Accept Tab 15
- Users Tab 15
- Domains Tab 15
- Advanced Tab 16
- Table 1.6: 17
- Chapter 2 19
- Pre-installation 19
- Deployment Types 20
- Pre-installation 21 21
- ISP Installation Deployment 22
- High Availability Deployment 23
- Chapter 3 25
- Step 2. Choose a Setup Type 26
- Table 3.1: 27
- Table 3.2: 28
- Port Forwarding 31
- MX Records 31
- Installation Examples 32
- Figure 3.2: 33
- Changing to Outbound Mode 34
- Table 3.4: 35
- Email Server Refer to 35
- Chapter 4 37
- Performance Statistics 38
- Subscription Status 39
- Monitoring the Message Log 40
- Classifying Messages 41
- Table 4.4: 42
- Button Description 42
- Overview of the Message Log 43
- Viewing Message Details 44
- Clearing the Message Log 44
- Table 4.6: 45
- Setting Description 45
- Table 4.7: 46
- Setting Description 46
- Table 4.8: 47
- Quarantine Type 47
- Location of Quarantined 47
- Messages 47
- Quarantine Responsibility 47
- Table 4.9: 48
- Table 4.10: 48
- Table 4.11: 49
- Table 4.12: 51
- Shutting Down the System 52
- Table 4.14: 53
- Table 4.15: 54
- Outlook Plu-In Description 54
- Resetting the Bayes Database 55
- Enabling Intent Analysis 56
- Reducing Backscatter 57
- Chapter 5 59
- Table 5.1: 60
- Blacklist Setting Description 60
- Table 5.2: 60
- Blacklist Service Description 60
- IP Address Filters 61
- Sender Domain Filters 62
- Sender Email Address Filter 63
- Attachment Type Filter 64
- Subject Line Filter 65
- Body Filter 66
- Header Filter 66
- Table 5.10: 67
- Chapter 6 69
- Managing Accounts and Domains 69
- Table 6.1: 70
- Column Description 70
- Table 6.2: 70
- Filter Description 70
- Editing User Accounts 71
- Table 6.3: 72
- User Feature Description 72
- To backup user settings: 74
- Setting Retention Policies 75
- Adding New Domains 75
- Editing Domain Settings 76
- Table 6.4: 77
- Table 6.5: 78
- Impact of a Down LDAP Server 80
- Table 6.6: 81
- Mail Server LDAP Setting 81
- Chapter 7 83
- Advanced Administration 83
- Table 7.1: 84
- Table 7.2: 86
- Performing Desktop Backups 87
- Restoring from a Backup File 88
- Spam Definition Updates 89
- Virus Definition Updates 90
- Table 7.8: 91
- Table 7.9: 93
- Syslog Field Description 93
- Table 7.10: 93
- Table 7.11: 94
- Cluster Set up Process 95
- Figure 7.1: 96
- Table 7.12: 96
- Table 7.13: 97
- Implementing Single Sign-on 99
- Enabling SSL 100
- Table 7.15: 101
- Table 7.16: 102
- Option Description 102
- Table 7.17: 103
- Field Description 103
- Troubleshooting 104
- Generating System Reports 105
- Specifying Report Properties 106
- Example Report 107
- Enabling SMTP over TLS/SSL 107
- Replacing a Failed System 108
- Reboot Options 109
- Table 7.22: 110
- Reboot Option Description 110
- Chapter 8 111
- Outbound 111
- About Outbound Mode 112
- Figure 8.1: 113
- Specifying Allowed Senders 114
- Table 8.4: 115
- Table 8.5: 115
- Table 8.6: 116
- Managing the Quarantine Box 117
- Table 8.7: 118
- Button Action 118
- Adding a Relay Server 119
- Chapter 9 121
- Quarantine Summary Report 122
- Table 9.1: 123
- Action Desciption 123
- Table 9.2: 124
- Appendix 1 129
- Regular Expressions 129
- Examples 130
- Regular Expressions 131 131
- \*FREE\* *FREE* 131
- Example Matches 131
- Appendix 2 133
- Exclusions and Restrictions 134
- Open Source Licensing 134
- Appendix 3 137
- Compliance 137
Produits connexes et manuels pour Logiciel Barracuda Networks 4
(130 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.018 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels